A custom made Submersible Fishing Waist Pack, made out of water proof fabric, sewed with seam tape and glued to help keep water tight. Waterproof zipper.

This Waist pack is 95% water proof. You can wade deep with it. Water Proof in rain. If you fall in and swim you might get a little water in at top corners or if waterproof zipper isn't zipped all the way closed and tucked under flap. 

What makes this Fishing Waist Pack unique is that it can slide from back to front and back again while wading in a river. 

See photo 3 and 4 – back view. This pack has two belts - optional: 

1. a two inch main belt wading belt - optional see options below (can use your wading belt if you want to save money)

2. a one inch belt that is used to tighten and hold the pack from slipping down. When you want to swivel this pack around loosen the one inch belt and pull on strap to move it forward. When you want to move it back pull on other side one inch belt and then re-tighten.

 Size: 19" X 8.5" | 2.9 liters (179 cu inches)

• Pack has one deep pocket
• Both belts are adjustable
• Seams are taped with double sticky bias tape
• All thread holes are sealed with thread tack to help keep dry
• Zipper is waterproof
• Made out of Ottertex(TM) Royal Blue Canvas Fabric, Waterproof Outdoor 600 Denier 
• Made and designed by Grabflies/Jeff Layton

 

This Chest Pack holds a lot for its size. It has two deep pockets, and one shallow pocket for tippet spools, clippers...

• Dimensions of wallet are 8 inches wide, by 10.5 inches high.
• Made out of Ottertex(TM) Royal Blue Canvas Fabric, Waterproof Outdoor 600 Denier. (Two colors in the pack, green and grey)
• One large deep zippered pocket for fly boxes
• One medium deep zippered pocket for cellphones ...
• one shallow pocket for tippet spools, clippers
• Adjustable chest wader suspenders strap included with pack.

Made in the USA by Jeff Layton

Made by a fisherman for fishermen

Only one available at this price.

This Waist Pack is like the the original Waist Pack (Click Here) but has two waterproof zippers and no rainfly.

A highly water resistant waistpack, 99% water proof - if you fall in stuff will remain dry, if you swim down the river a long way - maybe not? A waistpack made by a fisherman for fishermen. My waist pack is a very important piece of my fishing gear. As a double handed Spey caster, it is important to get bulk out of wading jacket or vest so my arms can cross my chest when make my sweeps to cast. Most of the time I don't need to get stuff out of waistpack while fishing. In the past when I did it was difficult and most of the time I had to wade to shore to get stuff from the pack. NOT any longer, with these new waistpack that I designed it rotates on the belt - pack isn't anchored to a strap, but instead has belt loops that allow it to side around. The Trampoline Mesh Fabric is stiff and slick enough to allow this.

• Outer Shell made out of Trampoline Mesh Fabric (Strong, Stiff Material - pliers slide easily into holster)
• Trampoline Mesh is a UV inhibited, monofilament polypropylene basket weave mesh - tough and strong.
• Inner Shell made out of Ottertex(TM) Royal Blue Canvas Fabric, Waterproof Outdoor 600 Denier.
• Belt loops (Two) on back accommodates belts up to three inches wide
• Dimensions: Width: 16 inches, Height: 9.5 inches (holds a lot of stuff)
• Waistpack is made with two layers - Inner layer shell made out of Waterproof Outdoor 600 Denier to keeps things dry.
• Sewing layers are all taped and sewed over tape, some areas are double tape to prevent water seepage.
• Pack has a Dr. Slick 5" Barb Pliers Holster, A mesh pocket for a tippet spool, and two deep pockets for flyboxes, flylines...
• Dr. Slick Oliers not included but can be added.
• Wading Belt Included.
• (This can be added see options below) Looped Strap and gourmet on side for Fish Tailing Mitt - sold separately (Fish Tailing Mitt click here)

A Reel and Rod Butt Protector for Spey Rods when broken down for travel, in the boat, or hike through the bush.

Works especially well with Grabflies Two Handed Fly Rod Sleeve Bag (click here) but also works without good.

Custom made by Jeff Layton | Grabflies - USA.

• Made out of Ottertex(TM) Royal Blue Canvas Fabric, Waterproof Outdoor 600 Denier.
• Made out of Softouch Padding Royal Blue - Inside Padding
• Velcro Top
• Fits Medium to Large Arbor Reels
• Rods 12 ft - 15 ft
• Dimensions: 14 inches long by 9.5 inches high

Inside look

A Water Resistant Fishing Waist Pack, made out of water proof fabric, sewed with seam tape to help keep water tight. Waterproof zipper.

Water Proof in rain. If you fall in and swim you might get a little water in at top corners or if waterproof zipper isn't zipped all the way closed and tucked under flap. 

See last two photos showing inside of pack's construction before it is turned inside out. Felled seams are glued with Vinyl HH-66 cement and waterproof fabric tape glued and sewn on over Felled seam. 

What makes this Fishing Waist Pack unique is that it can slide from back to front and back again while wading in a river. 

See photo 2 – back view. This pack has two belts: 

1. a two inch main belt

2. a one inch belt that is used to tighten and hold the pack from slipping down. When you want to swivel this pack around loosen the one inch belt and pull on strap to move it forward. When you want to move it back pull on other side one inch belt and then re-tighten.

 Size: 19" X 9"

• Pack has three pockets
• Both belts are adjustable
• Seams are taped with double sticky bias tape
• All thread holes are sealed with thread tack to help keep dry
• Zipper is waterproof
• Made out of Ottertex(TM) Royal Blue Canvas Fabric, Waterproof Outdoor 600 Denier 
• Made and designed by Grabflies/Jeff Layton
• Introductory Price of 1119.95
• Accessories: Grabflies Fish Tailing Mitt (CLICK HERE)  and Tote (CLICK HERE) + Grabflies Dr. Slick 5" Barb Pliers Holster (CLICK HERE)

A water resistant waist pack, made out of water proof fabric, sewed with seam tape to help keep water tight. Coil zipper that is overlapped with water proof material. Water can seep in at zipper's lock point. When wading deep it is possible for water to seep in.

 Size: 17" X 9"

• Seams are taped with double sticky bias tape
• All thread holes are sealed with thread tack to help keep dry
• Zipper is waxed
• Made out of Ottertex(TM) Royal Blue Canvas Fabric, Waterproof Outdoor 600 Denier 
• Made and designed by Grabflies/Jeff Layton
• Last Photo - Waist Pack with accessories - Grabflies Fish Tailing Mitt (CLICK HERE)  and Tote (CLICK HERE) + Grabflies Dr. Slick 5" Barb Pliers Holster (CLICK HERE)

Only one available at this price.

Adjustable Wading Belt, Made by Grabflies, Wader Belt

• 1 1/2” wide high-grade comfortable elastic webbing
• Quick-action side-release buckle
• Adjustable to 46”

Photo Shows Wading Belt and Accessories

See Accessories on Thumnails

Wading Staff Holster - custom made by Jeff Layton | Grabflies - USA.

This wading holster was made for myself - I was tired of losing and fighting wading holsters that came with my wading staffs. This wading stick holder is made out of Made out of Trampoline Mesh Fabric

• Trampoline Mesh is a UV inhibited, monofilament polypropylene basket weave mesh - tough and strong.
• Belt loop on back accommodates belts up to three inches wide

When I wade and need a Wading Staff, I may wade without one until I get in a rocky, or heavy current place in the river, then I reach for my wading stick. I need for my wading staff to slide out easily and slide in quickly. Also I wanted a more rigid wading stick holder so when I hike or move around it stays in place and doesn't bend or move. This does the trick.

Dimensions are 15 inches long, by 4.75 inches wide and holders a variety of wading staffs.

Fits belts up to two inches wide. 

Can add 1 1/2” wide high-grade comfortable elastic webbing, adjusts to waist up to 45 inches. 

Click thru images on upper left.

Example of different staffs that fit this holster.

Fish Tailing Mitt, Tailing Glove - custom made by GrabFlies.com/Jeff Layton (made in the USA)

Ready to strap onto your wading belt, waist pack... Also see Fish Tailing Mitt Tote (CLICK HERE)

Comes with snap clamp, strong elastic coil (One end is 304 stainless steel split ring, and the other end is the zinc alloy lobster clip) that stretches out to 59 inches. Mitt stays open for easy entry when fighting your fish. You can watch my videos and see this is what Grabflies has been using for years.

After years of being out of stock. I bought a new sewing machine and I’m (Jeff Layton) now making these again out of popular demand.

Strengths:

• Easier to get on – very important when fighting a fish
• This is actual netting – catch and release soft net material
• Better grip, with less force. Does not harm fish. 

 Fish netting is woven soft white nylon, no knots. Large mesh reduces water resistance and tangling. This netting is frequently used in catch and release nets.

A highly water resistant waistpack - if you fall in stuff will remain dry, if you swim down the river a long way - maybe not? A waistpack made by a fisherman for fishermen. My waist pack is a very important piece of my fishing gear. As a double handed Spey caster, it is important to get bulk out of wading jacket or vest so my arms can cross my chest when make my sweeps to cast. Most of the time I don’t need to get stuff out of waistpack while fishing. In the past when I did it was difficult and most of the time I had to wade to shore to get stuff from the pack. NOT any longer, with these new waistpack that I designed it rotates on the belt – pack isn’t anchored to a strap, but instead has belt loops that allow it to side around. The Trampoline Mesh Fabric is stiff and slick enough to allow this.

• Outer Shell made out of Trampoline Mesh Fabric (Strong, Stiff Material - pliers slide easily into holster)
• Trampoline Mesh is a UV inhibited, monofilament polypropylene basket weave mesh - tough and strong.
• Inner Shell made out of Ottertex™ Royal Blue Canvas Fabric, Waterproof Outdoor 600 Denier.
• Belt loops (Two) on back accommodates belts up to three inches wide 
• Dimensions: Width: 16 inches, Height: 9.5 inches (holds a lot of stuff)
• Rain Flap that covers YKK Finished Coil Zippers
• Rain Flap can be put into the up position to expose zippers using sewed in Velcro
• Waistpack is made with two layers – Inner layer shell made out of Waterproof Outdoor 600 Denier to keeps things dry.
• Sewing layers are all taped and sewed over tape, some areas are double tape to prevent water seepage.
• Pack has a Dr. Slick 5" Barb Pliers Holster, A mesh pocket for a tippet spool, and two deep pockets for flyboxes, flylines...
• Looped Strap and gourmet on side for Fish Tailing Mitt - sold separately (Fish Tailing Mitt click here)

 

 

 Only one available

Custom sewed by Grabflies.com/Jeff Layton (made in the USA)

Made out of high quality material:

Cordura® HP Royal Blue is a rugged, heavy-duty fabric woven from INVISTA™ textured high-quality polyester. This fabric features a clear polyurethane coating on the back and a durable water-repellent finish on the front for a long-lasting product that resists the elements and is easy to clean. You can distinguish the front of the fabric as it will have a shine-free finish compared to the slightly darker color and shine on the back side. This is a 915 x 1220 denier fabric.

Because of its great resistance to abrasion, mildew and rot, plus its quick-drying abilities, this high-performance polyester product is great for backpacks, custom bags, outdoor gear, footwear and sail bags. 

Sizes are listed below. Smaller sizes can always fit longer rods.  

Also see Fly Rod Handle Protector (Click Here)

Custom design by Grablies - Made in Washougal WA, USA.

Grabflies Dr. Slick 5" Barb Pliers Holster. Made by a fishermen for fishermen. When I go fishing and fly cast, I like to try and get as much gear off my chect as I can. Pliers have weight so I designed this Plier Holster so I can carry the pliers on my hip via my hip pack or wading belt.

• Holster comes with or without Pliers - see options below
• Holster is made to fit Dr. Slick 5 inch Barb Pliers - (Click Here to see pliers)
• Holsters is 5.5 inches long, and 3.25 inches wide
• Accomdates 2 - 2.75 inches belts. Belt loop is three inches wide - see back photo.
• Made out of Trampoline Mesh Fabric (Strong, Stiff Material - pliers slide easily into holster)
• Trampoline Mesh is a UV inhibited, monofilament polypropylene basket weave mesh - tough and strong.
• Two Options:
• 1. Add Loop to Hold Fish Mitt (see last two images from thumbnails upper left)
• 2. Add Pliers

Made in the USA by Jeff Layton

A custom made magnetic clip for flies, clippers, pliers, whatever you need for a temporary hold. Made by Jeff Layton, USA.

Just clip it on. Two versions, single magnet or double.

Examples of magnetic clip on fishing jacket or vest.

A leader tip wallet designed and made by Grabflies/Jeff Layton. Only available here.

This Tip Wallet is compact, designed to fit in your jacket, or vest pocket. Holds four coiled 10 - 15 ft tips.

• Dimensions of wallet are 5 inches wide, by 3.25 inches high.
• Made out of Trampoline Mesh Fabric
• Trampoline Mesh is a UV inhibited, monofilament polypropylene basket weave mesh - tough and strong.
• Four Pockets
• Velcro closing on fold over cover

Made in the USA by Jeff Layton

A Fly Line Wallet designed and made by Grabflies/Jeff Layton. Only available here.

This Fly Line Wallet is flexible and compact, designed to fit in your waist pack or pack. Holds four coiled Skagit and short Scandi heads.

Top photo - new color scheme. 

• Dimensions of wallet are 7.5 inches wide, by 7 inches high.
• Made out of Ottertex™ Royal Blue Canvas Fabric, Waterproof Outdoor  600 Denier. 
• Five, 7mm Polyester Hex Mesh Pockets
• Velcro closing on fold over cover

Made in the USA by Jeff Layton

This Chest Pack is small but has lots of storage and it takes me five hours non-stop to make.

• Dimensions of wallet are 9.5 inches wide, by 10.5 inches high.
• Made out of Trampoline Mesh Fabric (Strong, Stiff Material)
• Trampoline Mesh is a UV inhibited, monofilament polypropylene basket weave mesh - tough and strong.
• Made out of Ottertex™ Royal Blue Canvas Fabric, Waterproof Outdoor 600 Denier. 
• Two velcro Pockets
• One deep zippered pocket 
• Adjustable Shoulder Strap

        Click Photo for + 

Made in the USA by Jeff Layton

Only one available at this price.

A quick fly change system designed to work with Grabflies.com Infinitii Quick Change Swivel Tips (Click Here) . Quick Fly Change comes with Snap Hook (2 - one extra) and poly tubing slide lock (2 - one extra).

The practical idea is to go to the river with (4 - 6) flies pre-tied up and wound onto stiff foam spools (large enough to stop tippet from kinking with memory - rolls off ready to fish. Just tie your fly onto your favorite tippet mono, slide on the Poly tubing, then tie on the Snap Hook using an improved clinch knot - leave 1/3 of an inch tail piece (helps secure Poly tubing). I like to carry these spools with flies in a Mesh Tip wallet (Click Here) - they need to breathe and dry out after use and they do in these. I carry these in my wading jacket.

What do you get:

• One hard foam spool, 2.71 inches
• Two snap hooks
• Two poly tube locks
• Spool comes rigged with three feet of mono tied onto to snap hook with poly tubing - just tie on your fly.
• Accessory: Clip-On Ripple Foam Fly Patch
  

Custom Tip with Swivel by Grabflies (Options below start at 10 ft, can increase length to 15 ft) | Taking Sink Tips to a whole new level!

• Helps eliminate twists and fly tangles when you Spey cast, and swing flies.
• Allows your fly to swim better on the swing
• Make it easy to tie on tippets - just tie tippet onto swivel using improved clinch knot or Trilene knot.
• Also works great for single fly rods - eliminates line twist when fishing buggers.

Using a full 10 foot tip with swivel gives you a smoother transition and cast. Made using the best swivel with a 75 lb breaking strength.

Comes wrapped on Tip Tote (See Tip Tote)

Sizes: T-8, T-11, T-14, T-17, T-20 (Custom Size - Type in Length and T Material (T-8, 11, 14, 17, 20) + if longer than 10 ft select length under size option)

Also See: Fly Line Tip Swivel | 12 - 24 inch Tip Swive | Two Density Tip with Swivel | Two Loop Custom Tips

• Eliminate twists and fly tangles when you Spey cast, and swing flies.
  
• Make it easy to tie on tippets - just tie tippet onto swivel using improved clinch knot.
• Also works great for single fly rods - eliminates line twist when fishing buggers.

Length: 3 inches

• Scandi Swivel

See all Infinitii Fly Line Tip Swivels (Click Here)

Also see Spey Swivel Tips (Click Here)

Wader belt straps with stainless steel or plastic D-Ring. Clip on a wading staff or net...

Big enough to slide over large 2 inch wader belt buckles.

Custom made by Grabflies.com

• Eliminate twists and fly tangles when you Spey cast, and swing flies.
  
• Make it easy to tie on tippets - just tie tippet onto swivel using improved clinch knot.
• Also works great for single fly rods - eliminates line twist when fishing buggers.

Length: 3 inches

• Floating
• Intermediate (1.5 to 2 inches per second)
  
• T-8 Sinking Leader (slow sink) (anytime you are using a sinking tip)
• T-11 Sinking Leader (medium) (anytime you are using a sinking tip)
  
• T-14 Sinking Leader (fast) (anytime you are using a sinking tip)
• T-17 Sinking Leader (extra fast) (anytime you are using a sinking tip)
• T-20 Sinking Leader (extra fast) (anytime you are using a sinking tip)

Also see 12 - 24 inch Tip Swivel (T-11, T-14, T-17, T-20) (Click Here) and
Grabflies 10 Foot Tip with Swivel (Click Here)

Also see Spey Swivel Tips (Click Here)

Leader Tip Tote by Grabflies.com

Custom 10 Foot Tip with Swivel by Grabflies | Taking Sink Tips to a whole new level!

• Helps eliminate twists and fly tangles when you Spey cast, and swing flies.
• Allows your fly to swim better on the swing
• Make it easy to tie on tippets - just tie tippet onto swivel using improved clinch knot or Trilene knot.
• Also works great for single fly rods - eliminates line twist when fishing buggers.

Using a full 10 foot tip with swivel gives you a smoother transition and cast. Made using the best swivel with a 75 lb breaking strength.

Comes wrapped on Tip Tote (See Tip Tote)

Sizes: T-8, T-11, T-14, T-17, T-20

(Custom Size (Click Here) - Type in Length and T Material (T-8, 11, 14, 17, 20) + if longer than 10 ft select length under size option)

Also See: Fly Line Tip Swivel | 12 - 24 inch Tip Swive | Two Density Tip with Swivel | Two Loop Custom Tips

A GREAT Mono running/shooting line. Custom cut by Grabflies with loops added to both ends. Comparable to OPST Lazar Running Line

"This is the best running line I've ever used and shoots farther that Lazer line, plus holds up and doesn't tangle with twists" Jeff Layton

• Lightening Fast - shoots like a bullet
  
• EXTREME FIGHTING POWER FOR BIG GAME FISH
• Super strong – Incredible strength for confidence and control
• Shock resistant – Controlled stretch adds fighting power
• Extra tough and abrasion resistant –Tough against rough or sharp objects
• Diameter: .024" | .61 mm (40 lb)
• Three sizes: 20 lb, 30 lb, 40 lb (I use the 30 lb myself - Jeff Layton, same diamter as 40 lb OPST Lazer)
  

• Loops are long enough to loop around fly reel for quick loop to loop connection with your flyline.
• Loop tied using double surgeon knot and glued using:
  UV Knot Sense
• Length: 125 ft | 20 lb = 150 ft

Custom Two Density 10 Foot Tip with Swivel by Grabflies | Taking Sink Tips to a whole new level!

• Helps eliminate twists and fly tangles when you Spey cast, and swing flies.
• Allows your fly to swim better on the swing
• Make it easy to tie on tippets - just tie tippet onto swivel using improved clinch knot or Trilene knot.
• Like an iMow tip or other popular multiple density sinking tips but with a swivel.
• Casts better than a single density tip - weight forward sink tip.

Using a full 10 foot tip with swivel gives you a smoother transition and cast. Made using the best swivel with a 75 lb breaking strength.

Similar to Rio's very popular iMow Skagit Tips , but with different density leader material. No i = intermediate, starts with T-8, T-11, T-14 and then select a heavier sink tip with swivel portion to complete your ten foot tip.

Comes wrapped on Tip Tote (See Tip Tote)

Sizes: See Below under options

Also See: Fly Line Tip Swivel | 12 - 24 inch Tip Swivel| | Custom 10 Foot Tip with Swivel | Two Loop Custom Tips

Infinitii Spey Swivel made by Grabflies, attaches (via loop-to-loop connections) between the shooting line and shooting head and eliminates twists and kinks often caused by spey casting.

The difference between Grabflies "Infinitii Spey Swivel" and others on the market is that the loops are flyline welded to the best quality swivel (breaking strength 78 lb) on the market. The Flyline has a breaking strength of 30 lb, then doubled over, for an approximate strength of 50 lb.

I held off on making these as my first experience with Spey swivels was a hinging effect occurred during the D Loop, but with the doubled over flyline welded onto the swivels this isn't a problem. Since I use my Infinitii Swivel Tips I didn't need these for my fly presentation. What I found is that my Infinitii Spey Swivel can help your cast fly straighter as twists in the flyline are allowed to unwind, thus removing torque. Plus the bonus factor of helping your mono running line not get as many twists or kinks.

Size - Length: 4.5 inches

FlyTubes - Tube Fly Box made by GrabFlies.com

Also see NEW - FlyTubeCase (click here)

Crystal clear water proof plastic tubes, perfect for those Intruder flies, Moal Leeches, Stinger - trailing hook flies, Tube Flies...

Tubes come in two diameter sizes:1/2 inch (smaller Intruders, Moal Leeches, Marabou) and 3/4 inch (Large Intruders, Mega Moal Leeches)

Store and Protect Large Intruder Flies

Removable End Caps

Perfect for String Leech Flies

Perfect for String Leech Flies (3/4 inch Diameter Tube)6 inch length

Perfect for Moal Leeches (1/2 inch Diameter Tube) 3.5 inch length

"This is the only fly box I use now. In the summer I will put several skating or muddler type flies into one tube. For big steelhead flies it a must have item. I have tried so many different fly boxes, but it was always the bulk that gets in the way of Spey casting, or closing the lid down and munching the flash of marabou that gave birth to this simple fly storage solution." - Jeff Layton

An extension of the Fly Line Tip Swivel.

Leader material: T-11, T-14, T-17, T-20

Length: 12, and 24 inches

Use: A loop to loop connection to extend to your tip to help get the fly down more.

• Faster than changing your tip
• Can use as a cheater -15 - 40 grams
  
• Change (on and off) out when fishing different runs
  
• Fine Tune the depth of your fly during it's swing
• High Quality Swivel 75 lb breaking strength
• Weight T-17 = 20 grains

(Click to view larger)

Also see: Custom Grabflies 10 Foot Tip with Swivel

See all of the Infinitii Tips (Click Here)

A super Slick Fluorocarbon running/shooting line with with little to no memory and extremely low coefficient of friction for long distance casts.

This line really shoots. It is slick and the diameter very small for its strength. It is not recommended for direct loop to loop connection for Spey/Skagit lines seven weight or greater.

It is recommended HIGHLY for use withGrabflies Spey Swivel Shooting Handle - (click here)

Neoprene and Velcro Fly Rod Straps to keep your rod together to and from your fishing destination.

Use in your Car, Boat, or hiking into fishing spots. 

Usually Two Straps does the trick. 

Sold individually

Adjustable Wading Belt, Made by Grabflies

1.5-Inch Adjustable Black Nylon Wader Belt, up to 48 inches

Photo Shows Chest Belt Harness with Wading Belt

See Accessories on Thumnails (upper Left)

A 5 x 7 inch Gear Bag - a Wading Belt Accessory

Good for carrying Tippet Spools, Clippers... 

• Back - Trampoline Mesh is a UV inhibited, monofilament polypropylene basket weave mesh - tough and strong.
• Gear Pouch -  made out of Ottertex™ Royal Blue Canvas Fabric, Waterproof Outdoor 600 Denier.Belt loops (Two) on back accommodates belts up to Two inches wide 
• Dimensions: Width: 7 inches, Height: 5 inches
• Water resistant, Pouch is water Proof, water can come into zipper if you fall down and swim, water tight in rain.
• See All Wading Belt Accessories (Click Here)
• See Chest Belt Harness (Click Here)
• See Wading Belt for Accessories (Click Here)

Water Bottle Holders, Carrier, Tote designed and made by Grabflies.

Designed to fit 1.5 - 2 inch wading belts. Also great for hiking. Options allow you to buy this Water Bottle Holder alone, or with two choices for belts. 

Belt Loop on holder can accomodate belts up to two inches wide. 

Fits most water bottles for hiking and biking 16- 22 ounce type size. Up to 3.25 inch width and 9.5 inch circumference.

• 1.5-Inch Adjustable Black Nylon Wader Belt, up to 48 inches (Click Here)
• Elastic Wading Belt - 1 1/2” wide high-grade comfortable elastic webbing (Click Here)
• Bungee cord that adjusts for secure bottle hold. 

 This is part of Grabflies' Wading Belt Accessory Collection (See All - Click Here, New Window) 

Fish Tailing Mitt Tote designed and made by Grabflies.com (Jeff Layton)

This Mitt Tote has a sewed in belt loop that accommodates: 1" – 3” wading belts. Mitt Tote is made out of Top Notch 1S Fabric is a 600 denier solution-dyed polyester with a clear urethane back coating for marine and outdoor covers.

Options (See Option Selector below this description):

• Buy just the Tote
• Buy Tote and Fish Taling Mitt (See Fish Tailing Mitt - (Click Here)
• Buy Tote, Mitt, and Wading belt
• If you need a wading belt: 

• 1.5-Inch Adjustable Black Nylon Wader Belt, up to 48 inches (Click Here)
• Elastic Wading Belt - 1 1/2” wide high-grade comfortable elastic webbing (Click Here)

 This is part of Grabflies' Wading Belt Accessory Collection (See All - Click Here, New Window)

You can select this matching color green Fish Tailing Mitt Below.

This custom made Fly Tote can be used for toting around other things then it was design for.

Design for the (Infinitii Quick Fly Change) which I (Jeff Layton) have been using for two years now (3/18/2021). I love it. Makes changing flies easy and in low light essential for me.

A quick fly change system designed to work with Grabflies.com Infinitii Quick Change Swivel Tips (Click Here)

Note: Can also be used with a two inch mono loop to leader and then fly tie up. 

The Quick Fly Tote is 7.5 inches wide by 4 inches high. It can carry four 2.5 inch Diameter by .5 inch wide foam discs. (I usually carry three to save on bulk). Rounded lower edges to make it easier to side into a Wading Jacket pocket.

Made out of Trampoline and Waterproof Ottertex Canvas Fabric with coil zipper.

Option to add foam discs below, or Select Rigged Dsic's (Here) after adding to cart.

Made in the USA by Jeff Layton